NOTE:ALL FUEL PRODUCTS LISTED ARE FOR 10%ETHANOL FUEL OR
UNIVERSAL PLASTIC FUEL TANK --$49.99.
1 GALLON, 1/4" hose barb included
(must drill hole and tap for barb)
shim blocks may need made , for filler neck to come up through hood.)
(Fabrication required)
GAS CAP NOT INCLUDED, GAS CAP LISTED BELOW
KOHLER 10-14 HP BASIC TUNE UP KIT
KIIT INCLUDES THE FOLLOWING:
AIR CLEANER
PRE FILTER
CARB REBUILD KIT
SPARK PLUG
POINTS
CONDENSOR
CARB TO ENGINE GASKET
CARB TO AIR CLEANER GASKET
(pic for reference only)
10-14 HP OPEN SIDE, ANGLE FRAMES
$55.50
FUEL SYSTEM
ANGLE FRAME TRACTOR, TANK SHUT OFF VALVE
1/4" FUEL LINE 1/8 NPT
$12.99
PT1347
LGT SERIES, TANK SHUT OFF
1/4" FUEL LINE 1/8 NPT
$12.99
PT8546
UNIVERSAL INLINE SHUT OFF VAVLE
1/4" LINE
PT5841
$7.25
FUEL TANK CAP
2 " PLAIN CAP NO GUAGE
Fits close sided tractors.
$10.95
PT8935
REPLACEMENT GAS CAP(1977-1983)
REPLACES GAS CAP FOR PLASTIC TANKS, UNIVERSAL. MUST SPECIFY LENGTH FOR FLOAT ASSEMBLY.
I.D. OF CAP IS ...2 1/4 INCHES(2.250)
$28.99 for the 6 " length PT25352 (out of stock)
$35.99 for the 9 " length PT12074
We have gauge/caps that fit the universal tank, above as well.
(Also fits Wheel horse, Deers, Sears, and others
REPLACEMENT GAS CAP (1965-1976)
SOLD OUT
THANKS TO EVERYONE WHO PURCHASED ONE, WE HAD A GOOD RUN AT THEM ANYHOW!!!!
JUST IN ! ECONOMY FUEL CAPS, CHECK THEM OUT ON THE SECOND PARTS PAGE!!!
K SERIES KOHLER CARB REBUILD KIT#2575701-s
CARTER CARB REBUILD KIT FOR KOHLER CARBS. CARTER CARBS.
Replaces the following
2575702-S
2575701-S.
$15.50 plus tax and shipping.
CARB KITs WITH GASKETS
Includes
1 KOHLER CARB rebuild kit
1 intake gasket
1 carb to air cleaner housing gasket
OPEN SIDE LGT/ANGLE FRAME TRACTOR $28.99
(available for 8hp models too)
CLOSE SIDE TRACTOR $29.99
Close side tractor has OEM kohler gasket
#45 041 07-S
plus S&H
FORD YT 16/18 TRACTORS
Complete BRIGGS 16/18HP OPPOSED TWIN carb kit with gaskets
$32.99
PT#10086
FLOAT KIT FOR CARTER CARBS
KOHLER CARB, CARTER
Float and gasket, FOR CARTER CARBS
replaces Kohler# 25-757-03-s
$19.99
FLOAT BOWL CARTER CARBS
ALUMINUM AND STEEL BOWLS FOR CARTER CARBS
P.N.# MGD-35488
$20.80(alum) OUT OF STOCK
ANODIZED Steel $10.50
These also fit the BRIGGS CARTER MADE CARBS
WALBRO STYLE FLOAT BOWLS PN#12813 $10.99 (anodized steel)
KOHLER CARTER CARB MASTER REBUILD KIT $95.00/$105.00
PLEASE READ THIS ENTIRE PASSAGE BEFORE ORDERING!!
KIT INCLUDES THE FOLLOWING:
FLOAT BOWL
FLOAT AND PIN
FLOAT BOWL GASKET
FLOAT BOWL "O " RING
NEEDLE AND SEAT/ O RING
FLOAT BOWL SCREW GASKET
THROTTLE SHAFT
BUTTERFLY WITH SCREW
BUSHING FOR OBLONGED HOLES IN THE ALUMINUM BORE WHERE THROTTLE SHAFT SEATS.
INTAKE GASKET
AIR CLEANER GASKET
MUST STATE WHETHER YOU HAVE OPEN SIDE OR CLOSE SIDE TRACTOR, AIR CLEANER GASKETS ARE DIFFERENT!!!
ALSO YOU MUST STATE WHAT TYPE OF THROTTLE SHAFT YOU NEED, KNOB STYLE OR BOLT ON STYLE, AND WHETHER YOU NEED A BIG BUTTERFLY OR SMALL!!!! OR YOU CAN JUST REUSE YOUR OLD ONE, YOUR GETTING ONE REGARDLESS.
THESE KITS ARE FOR THE 10-16 HP SINGLE CYLINDER ENGINES, THEY MAY WORK WITH THE TWINS AND OTHER ENGINES, THAT IS UP TO YOU TO FIGURE OUT WHAT YOU WANT OR NEED.
ALSO, I DO NOT CARE IF YOU CAN BUY A CHEAP AFTERMARKET CARB ON EBAY FOR $30. YOU GET WHAT YOU PAY FOR. WAY BETTER TO REBUILD THE CARTER THAT CAME ON THE ENGINE.
$95 for ANGLE and OPEN SIDE LGT'S
$105 FOR CLOSE SIDE LGT'S
KOHLER CARB REPLACEMENT THROTTLE SHAFT KIT
NOTE: READ ENTIRE CONTENT
$13.27
WELDED ON KNOB (pic to right) PT71151
FLAT TOP WITH HOLE PT71141
Both styles have the small hole for the wire type, governor linkage.
Bushing to repair worn throttle shaft hole
$11.00 each.
You may have to reuse your old butterfly.Depending carb size
These fit Carter CARBS K series engines 8hp to 16hp.
A main cause for poor idle, throttle response, or backfiring out the carb, is a worn throttle shaf
FUEL FILTER OPEN SIDE 72-76
UNIVERSAL 1/4" LINE
$4.99
PT10347
NOTE: filters maybe clear,white or red in this style.
FUEL FILTER , CLOSE SIDE 77-83
UNIVERSAL 1/4" LINE
$6.25
PT10352
SEDIMENT BOWL 1/8 NPT
1/8"NPT
UNIVERSAL SEDIMENT BOWL
Will fit LGT tractors, cub cadet and others.
$16.95
PT1348
KOHLER K SERIES FUEL PUMP/ REBUILD KIT
BRAND NEW
PLASTIC BODY
CORRECT FLOW
REPLACES KOHLER#47-559-03S
FITS K241-K341(361)
ALSO M8,M10,12,14,16
$65.99PT10211
(FOR K181-PT15745)
NOW OFFERING A REBUILD KIT!!!
$11.99 INCLUDES NEW DIAPHRAGM GASKET AND SPRING.
ELECTRICAL/IGNITION
Universal Battery hold Down kit
$20.99
PLUS TAX AND SHIPPING
Comes with plastic universal battery retainer bracket (not pictured)
PT9249-9248
(the rods are 8" long)
On the LGT open sides, i drill holes right in the corner or bend of the battery tray. Then i run these kits through to hold the battery.
KOHLER OEM 15 AMP STATOR
FITS K SERIES AND OTHERS REPLACES KOHLER
PART #237878-S,2408501-S
PT71710
$100.66
(One year man. warranty)
OLD SCHOOL STARTER SOLENOID, UNIVERSAL FIT
This is the "old school" heavy duty solenoid switch. All metal body.
$45.99. PT1929
(One year man. warranty)
4 Pole STARTER SOLENOID (picture on the right)
$27.99 PN71847
ECONOMY UNIVERSAL 4 POLE SOLENOID
PT71847
$18.99
K SERIES KOHLER STARTER REBUILD KIT
PICTURE FOR REFERENCE ONLY
$29.99 Plus s&h
PT9219
KOHLER K SERIES STARTER
Replaces Kohler#45-098-09-s
$155.99 plus shipping
PT9802
(1 year man. warranty)
KOHLER K SERIES 12v IGNITION SWITCH
FITS JAC/FORD LGT series tractors from 1972-1983.
(will fit wheel horse, and cub cadet, and others with kohler k series engine)
$24.99plus s&h
PT8601
UNIVERSAL PTO SWITCH
Similar what was used on the Ford and Jacobsen lgt tractors. 5 prong, with safety interlock for Starter /neutral switch.
Factory connectors in harness will fit CLOSE SIDE tractors, and some OPEN side, but not all. P.N.#7675 -$29.99
VOLTAGE REGUALTORS
KOHLER K SERIES VOLTAGE REGULATOR
For open side Ford tractors, but will fit wheelhorse and others with 3 prong offset plug.
REPLACES KOHLER #25-403-22-S
$55.99 PLUS S&H
PT10297
(1 yr man. warranty)
KOHLER K SERIES VOLTAGE REGULATOR
"Close sided tractor"
REPLACES KOHLER #25-403-03-S
$39.99 PLUS S&H
PT10295
(1 yr man. warranty)
STARTER GENERATOR VOLTAGE REGULATOR
REPLACES DELCO# 1118988
$65.99PT1927
Yes i know EBAY is cheaper, but you also get what you pay for! Dont forget to ask your EBAY dealer about their 1 yr manufacture warranty.
For PRE 1972 tractors, ANGLE frame tractors, that have starter generator.
(1 year man. warranty)
KOHLER TUNE UP PARTS
KOHLER POINTS
BATTERY IGN.
REPLACES KOHLER PART# 47-150-63
$17.99
R-PT15530-MGD1823
KOHLER POINTS PUSH ROD
$22.99PT41104
KOHLER K SERIES CONDENSOR
REPLACES KOHLER#230722-S
$13.99
PLUS S&H
PT1844
or PT14953
CHAMPION SPARK PLUG #6932
FOR KOHLER K SERIES
H-10-C, CHAMPION SPARK PLUG
$4.99 PC(1)
FOR BRIGGS 16/18 HP
YT SERIES TRACTORS
RJ19LM
$4.50 EACH
2-REQUIRED
K SERIES COIL
KOHLER COIL FOR SINGLE CYLINDER ENGINES
These are correct for single cylinder applications. Your NAPA ford V8 COIL make look the same, but it is not.
$39.99
EXACT AFTERMARKET REPLACEMENT
PT1781
K SERIES COIL PLUG WIRE
PLUG WIRE FOR KOHLER
$24.99 EACH
PT71700
KOHLER ENGINES
KOHLER K SERIES ENGINE OVERHAUL KITS
K SERIES K241 -K321 (10-14HP)
(k341 available,but prices vary)
PISTON,RINGS,WRIST PIN, KIT
COMPLETE GASKET SET
BOTH CRANK SEALS
INT AND EX VALVES
CONNECTING ROD
BEARINGS, and what ever else you may need.
We also have a wide variety of Used kohler engine parts as well. From cranks to blocks, cylinder heads, tin work, flywheels etc. Just ask!
DUE TO EVERCHAINGING PRICE INCREASES AND AVAILABILITY WE NO LONGER PUT KITS TOGETHER, WE CAN GET YOU A QUOTE ON THE PARTS YOU NEED
"We can build your own kit, so no parts you dont need" Email for a quote.
Must specify std. .010, .020,.030 .040(12hp only)on piston size and crank size for connecting rods
prices vary on size and ENGINE!
KOHLER K SERIES HEAD GASKET
k181 8hp $10.99-- PT2763
K241-K321 10-14hp $12.99-- PT2764
k 341 16 hp $15.99 --PT2750
PLUS S&H
We also carry correct length and grade head bolts with washers for kohler flat heads for 10-16hp engines.
$2.50 each( includes 1 bolt,1 washer)
I do not carry the head studs.
KOHLER K SERIES ENIGNE BREATHER
KOHLER K SERIES BREATHER KIT
INCLUDES
2 GASKETS
BREATHER
$29.99
KOHLER K SERIES AIR CLEANER ELEMENTS
K SERIES K181 8 HP
AIR CLEANER $12.66
(4 1/4 ODX 3 ID X 2 1/4 TALL)
PT1385
K SERIES K241-K321. (SMALL air cleaner)
"OPEN SIDE/ANGLE FRAME" TRACTORS
1-3/4" X 4 3/4" X 6"
H X ID X OD
$11.24
PT1386
FOAM PRE FILTER FOR SMALL FILTER ABOVE
$4.40 PT1377
K SERIES K341 16 HP (OPEN SIDE TRACTOR 1972-1976)
3"H X 4 /3/4"ID X 6"OD
$16.28 plus s&h
PT1388
K SERIES K241-K341 MAGNUM/COMMAND (BIG air cleaner)
(CLOSE SIDED TRACTORS 1977-1983)
2 1/2" H X 5 1/2" ID X 7" OD
$16.99
PT1389
K SERIES KOHLER AND MAGNUM, "CLOSE SIDED TRACTOR"
"LOW PROFILE"
1-3/4"H X 5 1/2" ID X 7" OD
$14.99
PT2774
FORD YT 16/18 YARD TRACTOR
BRIGGS OVAL AIR CLEANER ELEMENT
$19.99
PT#2806
Other air cleaners available, just ask
KOHLER K SERIES MUFFLER
"CUB "style
1-1/4" inlet I.D.
$45.99 plus S&H
PT8284
KOHLER K SERIES "PEPPER"CAN MUFFLER
1" ID NPT, FITS KOHLER ENGINES 10-14 HP $14.95
1 1/4" ID NPT, FITS 16 HP KOHLER
$20.36
PT2285
KOHLER MUFFLER
"GRAVELY" style
i.d. inlet=1-5/16"
i.d. outlet=1-1/4"
$46.99
PT2286
BODY PARTS(MORE BODY PARTS ON 2ND PAGE, SEATS, GRILLES ETC.)
REPRODUCTION FRONT HUBCAPS
LIMITED SUPPLY
SET OF 2
FITS ALL 8" DEEP DISH WHEELS ON FORD GARDEN TRACTORS, WILL NOT FIT ANGLE FRAME SKINNY RIMS
$75.50 for two without decals
$100.00 PER SET(2) includes 2 decals
(hubcaps are not embossed like original, just a decal, see below)
$10 a pc for decals
FORD AFTERMARKET HUBCAPS
These are not recessed like the originals in the rear, nor are they embossed, like OEM.They use the outer rim and they have a hole for a valve stem. But they look good, and a fraction of the price compared to OEM. The stickers are just that, and are not on them, that is up to the purchaser to apply the decals.
AFTERMARKET BABY MOONS
SET OF 4 HUB CAPS FOR GARDEN TRACTORS
INCLUDES 2 FRONT 8"
AND 2 REAR 12"
$220 FOR THE SET OF 4 PLAIN
$244 FOR THE SET OF 4 W/ DECALS
$145 FOR REAR SET ONLY(NO DECALS)
$169 FOR REAR SET ONLY W/DECALS
DECALS ARE $12 EACH
Oliver Decals are custom made to order.
Ford decals are on stock
DECALS SEPERATE ARE $12 EACH
WILL FIT CUB CADET, WHEEL HORSE, SEARS, BOLENS ETC.
PLASTIC DUST CAPS
Fits FORD/JACOBSEN LGT series tractors from 1972-1983. (jacobsen1972-1987)
$10.99 plus shipping
(Will not fit "ANGLE" frame tractors)
FLOOR BOARD TRACTION TAPE
FLOOR BOARD TRACTION TAPE
Fits 72-76 or whatever you want to put it on.
6"x36" roll
Enough to do one tractor
$17.99 a roll
LGT FRONT BUMPER $140 plus shipping
AFTERMARKET FRONT BUMPER
Fits all tube frame tractors from 1972-1983.
FORD JACOBSEN OLIVER TRACTORS
These are USA MADE and twice as heavy as OEM. 3/16 STAINLESS STEEL CONSTRUCTION. CAN BE POLISHED.
LIMITED SUPPLY
BODY/FRAME PARTS
HEADLIGHT LENSES, PLASTIC
39.99 A SET
REPLACES FACTORY OEM
OEM TYPE TAILIGHTS
WHILE QUANTITIES LAST
$35.99 a set
1.75"X4"
Covers up factory holes...or maybe someones aftermarket holes.
LGT CLOSE SIDE PANEL REFLECTORS
These are very similar to OEM reflectors, size and style. Self adhesive
$6.99
LGT CLOSED SIDE LOWER DASH PANELS
MAIN CENTER SECTION $45
SIDES $20 EACH
LGT CLOSE SIDE UPPER DASH
UPPER DASH "U "-$35
SIDES $22 EACH
OPEN SIDE HOOD HARDWARE KIT
KIT CONTAINS :
4 SPEED NUT/CLIPS
4 RUBBER WASHERS
4 THUMB SCREWS
$15.99 per kit
plus S&H:
This kit will also fit the LT series tractors.
DELUXE OPEN SIDE HOOD HARDWARE KIT
KIT CONTAINS :
4 SPEED NUT/CLIPS
4 RUBBER WASHERS
4 THUMB SCREWS
4 LARGE FLAT WASHERS
$17.99 per kit
plus S&H:
STAINLESS OPEN SIDE HOOD HARDWARE KIT
KIT CONTAINS :
4 SPEED NUT/CLIPS
4 RUBBER WASHERS
4 PHILIPPS S.S. 5/16-18, SCREWS
4 S.S FLAT WASHERS
$21.35 per kit
plus S&H
HOOD HARDWARE UPGRADE KIT
$8.00 plus s&h
4- 5/16" I.D. X 1.25" O.D.
STAINLESS BLACK OXIDE WASHERS (CAN BE PAINTED)
316 STAINLESS STEEL WASHER
UPGRADE TO $10.00( CAN BE POLISHED)
EITHER KIT HAS THE RUBBER WASHERS INCLUDED.
4 - 1/8" THICK X 1.25" O.D. RUBBER WASHERS
This kit is for hoods with worn oblong holes. Works well with hood hardware kit above.
FENDER PAN BODY MOUNTS---$45.99
SET OF 8,
4--5/16" FOR REAR
4--1/4 " FOR FOOT RESTS
NOTE: The front isolators have a screw in bolt from the top, the bottom side of the isolator is all thread stud.
These are the "CLOSE SIDED TRACTOR" style, but will fit the open side as well.
I have 2 types of screws,pan head and concave. Pan head are for the "close" side tractors, concave are the "open" side tractors. The 2 types of tractors had different foot rests.
I do stock the all thread type top and bottom, like the original factory OEM, from the "open" side tractors, but the all thread will need cut to length.
When ordering let me know what style tractor you have, these way i give you the right screws for the foot rests.
HOOD BUMPERS (FOR 72-76 LGTS)--$11.99
SET OF 4
2-BEHIND HEADLIGHT PAN
2 -FOR GAUGE CLUSTER
INCLUDES MOUNTING HARDWARE.
FITS OPEN SIDE FORD AND JACOBSEN GARDEN TRACTORS AND LT MODELS
STEERING UPGRADE THRUST BEARINGS
$12.00 each (3pc kit as seen in pic)
3/4" I.D.........1 1/4" O.D.-SPINDLE
5/8" I.D..........1 1/4 O.D. -COLUMN
USED ON STEERING BOX UPGRADE OR SPINDLE UPGRADE.
I put these on my 165 front loader and made a huge difference, They replace the washers on the spindles.
part #tc1220
Steering column thrust bearings, goes behind the double nut on the column gear box, cross shaft.
LGT ROSS STEERING BOX BEARINGS
LIMITED SUPPLY
$32.99
Includes , retainer and race
LGT ROSS STEERING BOX GASKET
$15.99 EACH
LGT ROSS STEERING BOX REBUILD KIT
$89.99 EACH KIT
Kit includes:
SHAFT BEARING KIT
GASKET
WORM GEAR PIN/CAM FOLLOWER AND NUT :Must specify whether you have a 1/2 " or 9/16" pin.
THRUST BEARINGS AND WASHERS.
THRUST BEARING KIT(use this behind the double nuts against the steering box on the cross shaft.)
ATTENTION: The cam followers(threaded pin with nut) were different on different model tractors, some were 1/2" some were 9/16".
You must specify which you need. Most open side were 1/2". They changed to 9/16" somewhere in the mid 70s. I am not sure if all close side has the large pin or small. Take yours out and measure!!!
I HAVE 2 TRACTORS SITTNG HERE IN THE JUNK YARD AND EACH HAVE DIFFERENT SIZES!!!
CLOSE SIDE ENGINE MOUNTS
Fits 77-83 LGT CLOSE SIDE TRACTORS
$17.99 EACH
$69.99 SET OF 4
$10.99 HARDWARE KIT FOR SET OF 4.
ANGLE FRAME & ATTACHMENT BELTS
ANGLE FRAME 66-71 SNOWBLOWER BELT
PT#7508 $24.00 (KEVLAR)
PT#5098 $12.65
REAR TILLER PT#7605 $36(KEVLAR)
PT#5187 $28
36" TIMED BELT FOR STEEL DECKS
$15.99
36" STEEL DECK DRIVE BELT
PT#7511 $24.00
42" ALUMINUM DECKS
PT#13718 $64.00
10/12 HP STARTER GENERATOR
PT#5015 $8.03
PT#1437 $14.25 (KEVLAR)
10/12 HP HYDRAULIC LIFT
PT# 5061 $8.03
PT#7433 $13.00 (KEVLAR)
8HP HYDRAULIC LIFT
PT#5059 $8.03
PT#7469 $15 (KEVLAR)
1961-1965 3 SPEED JACOBSEN TRANSMISSION BELT(not for 4 speed peerless)
PT#7626 $45.99
1966-1971 ANGLE FRAME TRASNMISSION BELTS
HYDRO PT#7617 $37.15
GEAR PT#7622 $37.15
TUBE FRAMETRANSMISSION BELTS
FORD LGT/JAC GT TUBE FRAME FORD/JAC GEAR DRIVE 1972-1983/87OPEN AND CLOSE SIDE
TRACTORS TRANS (92)-$26.53
KEVLAR MADE IN USA
42" LGT DECK BELTS
72-83 LGT 42" cut, Deck Measures 50"
LGT 42" DECK BELT--$20.00(#5116)
KEVLAR -$28.99(USA)(#7526)
PTO BELTS, RUN FROM THE ELECTRIC PTO TO THE MOWER DECK!
PTO BELT-------$20.00(#5113)
KEVLAR-$28.99(USA)(#7523)
ALL KEVLAR BELTS ARE HEAVY DUTY AND MADE IN THE USA!
42" LGT BLADES
SOLD OUT!!!!
42" CUT -(deck shell measures 50")
set of 3 $
price change and temporary out of stock
These are the last of the production run.
while quantities last.
We may have used blades at any given time as well, they will be sold as is!
72-83 LGT 50"CUT BLADES $140.00 SOLD OUT!!!!
REPLACEMENT FOR PART#
JAC50095
COMPLETELY SOLD OUT!!
WAS FUN WHILE IT LASTED, THANKS TO ALL THE CUSTOMERS WHO PURCAHSED THESE FINE AMERICAN BUILT PRODUCTS!!! WE will no longer be making these until further notice.
The blade you receive may not look like the picture to the left, it is for reference only. In fact, it wont even look like OEM blades, but it will fit and mow just the same if not better.
THESE BLADES ARE CUSTOM MACHINED TO FIT THE JACOBSEN HUB. SO the part number ON THE BLADE will not be a JACOBSEN PART NUMBER!!!! DO NOT GET CONFUSED, I do that enough.
This deck measures 59" !!!!
(These will not fit the 42" deck, which measures 50" )
MEASURE YOUR DECK SHELL!!!!
We are the only place that sells the 50" blades.
DISCLAIMER: These parts are brand new, but custom machined therefore, they are considered pre owned or used. Overly Equipment, Oregon, Rotary, STENS, MAPLE GROVE and the likeness of the companies are not responsible for property damage, personal injury or death, from the use of this part. It is the owners responsibility for the inspection and care of their equipment. This part is non refundable and is "as is". This claim is accepted when buyer purchases this product.
PIC IS FOR REFENERCE ONLY NOT ACUTAL BLADE PICTURE.
72-83 LGT, 50" CUT , DECK measures 59"
50" DECK BELT (Belt thatis on the deck)
ECONOMY BELT-$22.50(#5130)
KEVLAR BELT-$31.99(MADE IN USA)#7540)
PTO BELTS RUN FORM THE ELECTRIC PTO TO THE MOWER DECK!
ECONOMY PTO BELT-------$20.00(#5116)
KEVLAR PTO BELT--$26.59(MADE IN USA)(#7526)
BELTS ARE HEAVY DUTY KEVLAR
Made in the USA
FORD LGT DECK ROLLER
LENGTH-6"
DIAMETER-2.5"
I.D.-9/16"
$17.90 PLUS SHIPPING AND TAX
#14467
FORD LGT "SHORT" Deck Roller
3/8 bore
$14.99 each.
PULLEYS
V-BELT IDLER PULLEYS
( fits LGT series mule drive, AND angle frame decks. Also a substitute for gilson built Ford/lawn boy mule drives)
0.D.--3--3/16"- BORE -3/8"-11/16"WIDE--$11.99..... PT728
O.D.--3" BORE-3/8"-3/4WIDE -$11.63....PT730
O.D.--3.5"-BORE 3/8"--$12.75...PT2182
O.D.--4"--BORE-3/8"--$16.75..... PT733
O.D.--4.5"--BORE-3/8"-$-$25.99......PT2183
O.D--3.75--BORE -11/16"-$29.99...PT15606
O.D-3.375-BORE5/8"-$34.99 PT9895
FLAT IDLER PULLEYS
O.D. --4-3/8," BORE- 5/8"
LGT TUBE FRAME TRANSMISSION CLUTCH/BELLCRANK ,LGT 100 AND 120 GEAR DRIVE TRACTORS ONLY
ALSO FITS ANGLE FRAME MOWER DECKS AND CLUTCH PEDAL ASSEMBLY
$33.99
PT13424
O.D.--4.5" BORE- 3/8"--$23.99(fits LGT series decks)PT11633
O.D--3 1/8"--BORE-3/8"--(CERTAIN LGT REAR PTO)
$18.75 PT2176
V BELT DRIVE PULLEYS
O.D. 4"--BORE 1" w/ keyway--$22.99( fits LGT series1972-1983 only!deck hubs, outside two, not middle main drive double pulley.
pt774
INSTALLATION KIT FOR PULLEY $7.00 (5washer kit)
https://www.youtube.com/watch?v=D4-ZIPeOp_A
O.D.4"--BORE-3/4" , w/keyway---$20.75--pt322
(fits the 1984 and up LGT 42" DECKS for jacobsen tractors)
IF YOU DO NOT SEE A PULLEY, WE CAN GET YOU A PRICE, JUST GIVE US THE I.D AND O.D. and we can quote
LGT DECK MAIN DRIVE TOP PULLEY
This is the top pulley of the double pulley, on the Drive spindle of the LGT deck.
MADE WITH PRIDE IN THE USA, MT. PLEASANT PA.
Replaces JAC PART#330809=42" DECK
JAC PART#330810=50"DECK
$45.99 PLUS S&H 42" CUT
$47.99 PLUS S&H 50" CUT
LGT DECK MAIN DRIVE BOTTOM PULLEY
This kit comes with a new bottom pulley, top pulley, spindle machined to the pulley and the hardware, plus 2 bearings. This is a custom built, here in the USA, to REPLACE the OEM style bottom pulley which is obsolete.
REPLACES #JAC330651
No one else in the world makes this and it is built with pride in MT PLEASANT PA.
This will fit the 50" cut as well, but there is a belt difference.
$189.99
DECK HANGER BUSHINGS
Custom milled to OEM Specs.
100% made in the USA, and by local PA machine shop! Picture is for reference, bushings are oil embedded steel alloy.
$6.55 EACH
DECK HANGER SHOULDER BOLTS
NOS AND USED AVAILABLE
$8.00 NOS,EACH
$4.00 USED, BUT GOOD
OUT OF STOCK!!!
5/8X1/2" SHOULDER 3/8X16 THREADS 7/8 LONG THREADS.
DECK HANGER BOLT KIT
BRAND NEW
BOLT/LOCK NUT/SPACER/WASHERS
WILL REPLACE ENTIRE OEM BUSHING AND SHOULDER BOLT
$7.99 EACH
BLADE HUB/ADAPTERS
N.O.S. while supplies last
$39.99 each
USED AVAILABLE $25.99 EACH
When and if available, email for inquirey
N.O.S. FORD LT BLADE HUB/ADAPTERS/SPACER
N.O.S. while supplies last
$35.99
jac 203438
Discontinued at New Holland
FITS LT 36" MOWER DECK, not 100% on exact models, even NEW HOLLAND dealers dont know for sure. Check your model and serial numbers.
OEM DECK TENSION SPRING- LGT TRACTORS
$35.99
Built to OEM SPECS!!! BUILT WITH PRIDE IN THE USA, BY KENTUCKIANS!!
DECK BEARINGS
OEM REPLACEMENTS
FITS 42" AND 50" LGT DECKS
$8.50 A PC.
10303