To place and order, email us. Make sure to include your full name, shipping address and method of payment, PAYPAL, money order, business check,or credit card. Credit card users please call 724 216 4913, if we do not answer please leave a message and telephone number and we will call you back as soon as we can. Thanks
555 Dry Hill Road, Connellsville, Pennsylvania 15425, United States
(724) 216-4913 All orders carry std $50 insurance, if you want more you need to state so.. All orders are susceptible for credit card, PAYPAL fees/charges and taxes where applicable.
1/2 X 20 FINE THREAD TIE ROD END BALL JOINT FOR 66-71 ANGLE FRAME AND 72-83 TUBE FRAME TRACTORS
(DOUBLE CHECK YOUR SIZE BEFORE ORDERING, SOME PREVIOUS OWNERS OF YOUR TRACTOR MAY HAVE SWAPPED OUT STEERING PARTS!)
$13.95 EACH PLUS S&H
$10.95 PLUS S&H
3/8x24 TIE ROD END
$4.80 PLU S&H
1 3/8" O.D.
Check your wheels before ordering! Someone may have swapped out wheels over time. Hub and bearing dimensions are different for different wheels.
2"X1" SPINDLE BEARINGS
Replaces JACOBSEN part #345050
$7.55 a pc.
Replaces part #788049
$19.99 a pc.
(picture for reference only)
$52.99 plus s&h
Replaces the inline obsolete filter on all tube frame LGT tractors. Not for angle frame tractors
Note: Some hard lines may need tweaked, loosened for fitment, extra fittings provided, not seen in pictures.
Same as in kit above, aluminum housing only
KOHLER COIL FOR SINGLE CYLINDER ENGINES
EXACT AFTERMARKET REPLACEMENT
FITS KOHLER FLATHEAD TWIN ENGINES
REPLACES KOHLER #(52-755-48-S)
M18 M20 MV16 MV18 MV 20 COILS
FITS HORIZONTAL AND VERTICAL SHAFT (L HEAD) ENGINES
PLUG WIRE FOR KOHLER
FITS 1977-1983 FORD JAC LGT TRACTORS
$65.99 FOR 4
$10.99 HARDWARE KIT
16 caps screw, lock washers, nuts
FITS K SERIES AND OTHERS REPLACES
ALUMINUM AND STEEL BOWLS FOR CARTER CARBS
ANODIZED Steel $10.00 part#13455.
These also fit the BRIGGS CARTER MADE CARBS
FITS LATER KOHLER K SERIES, MOSTLY ON CLOSE SIDED
$8.99 COMES WITH 0 RING
Carter style aftermarket carbs.
$79.99 10-12HP- p.n#MGD61069
UNIVERSAL FUEL BOWL
Will fit LGT tractors, cub cadet and others.
UNIVERSAL 1/4" LINE
UNIVERSAL 1/4" LINE
WELDED ON KNOB #71151 (pic to left)
FLAT TOP WITH HOLE#71141.
Both styles have the small hole for the wire type, governor linkage.
Bushing to repair worn throttle shaft hole
You may have to reuse your old butterlfy, pending carb size. These fit Carter CARBS K series engines 8hp to 16hp.
A main cause for poor idle, throttle response, or backfiring out the carb, is a worn throttle shaft.
KOHLER CARB, CARTER
Float and gasket, FOR CARTER CARBS
replaces Kohler# 25-757-03-s
4 SPEED NUT/CLIPS
4 RUBBER WASHERS
4 tHUMB SCREWS
$11.15 per kit
$7.00/$12.00 plus s&h
4- 5/16" I.D. X 1.25" O.D.
STAINLESS BLACK OXIDE WASHERS (CAN BE PAINTED)
316 STAINLESS STEEL WASHER
UPGRADE $5.00( CAN BE POLISHED)
4 - 1/8" THICK X 1.25" O.D. RUBBER WASHERS
This kit is for hoods with worn oblong holes. Works well with hood hardware kit above.
1" ID NPT, FITS KOHLER ENGINES 10-14 HP $14.95 P.N.#1277
1 1/4" ID NPT, FITS 16 HP KOHLER
$20.36 P.N.# 2285
Similar what was used on the Ford and Jacobsen tractors. 5 prong, with safety interlock for Starter /neutral switch.
Factory connectors in harness will not fit. New wire connectors will be needed.
#mgd 7675-$19.99 (different prong location)
PLASTIC LENSE SET OF 2
$29.99 plus shipping
$17.99 single lense
Fits all JAC built tractors with rectangle lights. Also replaces the SPEAKER GLASS 777 which are no longer available. We get the Glass speaker 777 in,used, now and then, so just ask.
$35.99 PLUS SHIPPING
Not exact replacement, but big enough to cover all the holes by factory or by someone using AUTO PART store generics. They measure 1.75 x 4"
FITS 1" SPINDLES
BOTH STYLES 1.5" AND 1.125 "TALL
$20.00 plus shipping
While supplies last!
Enough to do both sides of the floor boards
$14.99 1 ROLL
Exact replacement for REAR PTO shaft on LGT series tractors.
$13.46 plus s&h
KEVLAR, MADE IN USA
EXACT REPLACEMENT END BEARINGS FOR LGT REAR PTO SHAFTS
72-83 JACOBSEN FORD TRACTORS
$39.99 FOR 2 BEARINGS, AND 4 RETAINERS.
picture for reference only
REPLACES THE FACTORY WOODEN BLOCK, IN FRONT OF BACK TIRE, ON THE ANGLE PART OF THE FRAME.
picture is for reference only
This replaces the original idler pulley on the "OPEN SIDE TRACTOR" 72-76, REAR PTO.
This is a carbon composite pulley, not steel, they work great too. I replaced my original with one of these on my "MINI 9600", and never looked back.